コンソール |
U-Boot 2010.03 (Nov 28 2012 - 03:11:12) Board: EX4550-32T 4.8 EPLD: Version 9.0 (0x08) DRAM: Initializing Configuring DDR for 800 MT/s data rate DDR: 2 GB FLASH bank: 0 FLASH: 8 MB Firmware Version: 01.00.00 pci_init_board: devdisr=7083000, io_sel=f PCIE1 connected to Slot as Root Complex (base addr fef0a000) Scanning PCI bus 01 PCIE1 on bus 00 - 08 USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Consoles: U-Boot console FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.4 (builder@kessuth.juniper.net, Wed Nov 28 02:41:47 UTC 2012) Memory: 2048MB bootsequencing is enabled bootsuccess is set new boot device = disk0 Loading /boot/defaults/loader.conf kernel data=0xa9cd08+0xb01d0 syms=[0x4+0x905c0+0x4+0xd3c23] Hit [Enter] to boot immediately, or space bar for command prompt. Booting [/kernel] in 1 second... Booting [/kernel]... Kernel entry at 0x800000c0 ... GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1996-2018, Juniper Networks, Inc. All rights reserved. Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. JUNOS 12.3R12-S12 #0: 2018-12-28 12:55:38 UTC builder@kuzuryu.juniper.net:/volume/build/junos/12.3/release/12.3R12-S12/obj-powerpc/junos/bsd/kernels/JUNIPER-EX/kernel can't re-use a leaf (all_slot_serialid)! Timecounter "decrementer" frequency 75000000 Hz quality 0 cpu0: Freescale e500v2 core revision 5.1 cpu0: HID0 80004080 real memory = 2121269248 (2023 MB) avail memory = 2080358400 (1983 MB) Security policy loaded: JUNOS MAC/pcap (mac_pcap) Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot) Security policy loaded: Junos MAC/veriexec (mac_veriexec) MAC/veriexec fingerprint module loaded: SHA1 MAC/veriexec fingerprint module loaded: SHA256 ETHERNET SOCKET BRIDGE initialising Initializing EXSERIES properties ... nexus0: ocpbus0: on nexus0 openpic0: iomem 0xfef40000-0xfef600b3 on ocpbus0 memctl0: iomem 0xfef20000-0xfef20e5b,0xfef02000-0xfef02e5b irq 32,34 on ocpbus0 i2c0: iomem 0xfef03000-0xfef03014 irq 59 on ocpbus0 ds1672 rtc0: on i2c0 i2c1: iomem 0xfef03100-0xfef03114 irq 59 on ocpbus0 uart0: iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0 uart0: console (9600,n,8,1) uart1: iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0 lbc0: iomem 0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 35,17 on ocpbus0 cb fpga: un-supported RE/board:130 cfi0: iomem 0xff800000-0xffffffff on lbc0 cb fpga: un-supported RE/board:130 syspld0 iomem 0xff000000-0xff00ffff on lbc0 tsec0: iomem 0xfef24000-0xfef24fff irq 45,46,50 on ocpbus0 tsec1: iomem 0xfef25000-0xfef25fff irq 51,52,56 on ocpbus0 tsec2: iomem 0xfef26000-0xfef26fff irq 47,48,49 on ocpbus0 tsec2: hardware MAC address 3c:8a:b0:ed:32:7d miibus0: on tsec2 brgphy0: on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto pcib0: iomem 0xfef0a000-0xfef0afff,0xc0000000-0xcfffffff irq 42 on ocpbus0 pci0: on pcib0 pcib1: at device 0.0 on pci0 pci1: on pcib1 pcib2: irq 21 at device 0.0 on pci1 pci2: on pcib2 pcib3: irq 0 at device 1.0 on pci2 pci3: on pcib3 mpfe0: mem 0xc0000000-0xc3ffffff irq 20 at device 0.0 on pci3 mpfe_adcr_shadow_alloc: allocated idx: 0 pcib4: irq 0 at device 2.0 on pci2 pci4: on pcib4 mpfe1: mem 0xc4000000-0xc7ffffff irq 20 at device 0.0 on pci4 mpfe_adcr_shadow_alloc: allocated idx: 1 pcib5: irq 0 at device 3.0 on pci2 pci5: on pcib5 mpfe2: mem 0xc8000000-0xcbffffff irq 20 at device 0.0 on pci5 mpfe_adcr_shadow_alloc: allocated idx: 2 pcib6: irq 0 at device 4.0 on pci2 pci6: on pcib6 mpfe3: mem 0xcc000000-0xcfffffff irq 20 at device 0.0 on pci6 mpfe_adcr_shadow_alloc: allocated idx: 3 pcib7: irq 0 at device 5.0 on pci2 pci7: on pcib7 pcib8: irq 0 at device 6.0 on pci2 pci8: on pcib8 ehci0: iomem 0xfef22000-0xfef22503 irq 44 on ocpbus0 usb0: EHCI version 1.0 usb0 on ehci0 usb0: USB revision 2.0 uhub0: Freescale EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub0: 1 port with 1 removable, self powered uhub1: vendor 0x0424 product 0x2513, class 9/0, rev 2.00/b.b3, addr 2 uhub1: multiple transaction translators uhub1: 3 ports with 0 removable, self powered umass0: ATP Electronics ATP IG eUSB, rev 2.00/11.00, addr 3 Initializing product: 126 .. bmeb: bmeb_lib_init done 0x8436b000, addr 0x80a9e1c0 bme0:Virtual BME driver initializing ###PCB Group initialized for udppcbgroup ###PCB Group initialized for tcppcbgroup Kernel thread "wkupdaemon" (pid 43) exited prematurely. da0 at umass-sim0 bus 0 target 0 lun 0 da0: Fixed Direct Access SCSI-4 device da0: 40.000MB/s transfers da0: 1919MB (3930112 512 byte sectors: 255H 63S/T 244C) Trying to mount root from ufs:/dev/da0s1a Attaching /packages/jbase via /dev/mdctl... Mounted jbase package on /dev/md0... Verified manifest signed by PackageProduction_12_3_0 Verified jboot signed by PackageProduction_12_3_0 Verified jbase-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted fips-mode-powerpc package on /dev/md2... Verified manifest signed by PackageProduction_12_3_0 Verified fips-mode-powerpc-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jcrypto-ex package on /dev/md4... Verified manifest signed by PackageProduction_12_3_0 Verified jcrypto-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jdocs-ex package on /dev/md6... Verified manifest signed by PackageProduction_12_3_0 Verified jdocs-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jkernel-ex package on /dev/md8... Verified manifest signed by PackageProduction_12_3_0 Verified jkernel-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jpfe-ex45x package on /dev/md10... Verified manifest signed by PackageProduction_12_3_0 Verified jpfe-ex45x-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jroute-ex package on /dev/md12... Verified manifest signed by PackageProduction_12_3_0 Verified jroute-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jswitch-ex package on /dev/md14... Verified manifest signed by PackageProduction_12_3_0 Verified jswitch-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Mounted jweb-ex package on /dev/md16... Verified manifest signed by PackageProduction_12_3_0 Verified jweb-ex-12.3R12-S12 signed by PackageProduction_12_3_0 Executing /packages/mnt/jweb-ex-12.3R12-S12/mount.post.. Automatic reboot in progress... ** /dev/da0s1a ** Last Mounted on /altroot ** Root file system ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 1526 files, 66677 used, 107165 free (29 frags, 13392 blocks, 0.0% fragmentation) ** /dev/da0s3e ** Last Mounted on /var ** Phase 1 - Check Blocks and Sizes INCORRECT BLOCK COUNT I=7816 (4 should be 0) CORRECT? yes INCORRECT BLOCK COUNT I=15706 (208 should be 196) CORRECT? yes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts UNREF FILE I=23453 OWNER=0 MODE=140600 SIZE=0 MTIME=Feb 4 10:39 2023 CLEAR? yes UNREF FILE I=23480 OWNER=0 MODE=140600 SIZE=0 MTIME=Feb 4 10:26 2023 RECONNECT? yes ** Phase 5 - Check Cyl groups FREE BLK COUNT(S) WRONG IN SUPERBLK SALVAGE? yes SUMMARY INFORMATION BAD SALVAGE? yes ALLOCATED FILE 17 MARKED FREE BLK(S) MISSING IN BIT MAPS SALVAGE? yes 388 files, 674 used, 121804 free (180 frags, 15203 blocks, 0.1% fragmentation) ***** FILE SYSTEM MARKED CLEAN ***** ***** FILE SYSTEM WAS MODIFIED ***** Computing slice and partition sizes for /dev/da0 ... savecore: Router rebooting after a normal shutdown... No dump exists ** /dev/da0s3d ** Last Mounted on /var/tmp ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 13 files, 78 used, 359583 free (39 frags, 44943 blocks, 0.0% fragmentation) ***** FILE SYSTEM MARKED CLEAN ***** ** /dev/da0s4d ** Last Mounted on /config ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 18 files, 21 used, 59173 free (29 frags, 7393 blocks, 0.0% fragmentation) ***** FILE SYSTEM MARKED CLEAN ***** rm: /var/etc/pam.conf: Operation not permitted Creating initial configuration...mgd: Running FIPS Self-tests veriexec: no signatures for device. file='/sbin/kats/cannot-exec' fsid=74 fileid=51404 gen=1 uid=0 pid=503 mgd: FIPS Self-tests Passed mgd: commit complete Setting initial options: debugger_on_panic=NO debugger_on_break=NO. Starting optional daemons: . Doing initial network setup: . Initial interface configuration: additional daemons:. Additional routing options:kern.module_path: /boot//kernel;/boot/modules -> /boot/modules;/modules/peertype;/modLoading the EX-series platform NETPFE module ules/ifpfe_drv;/modules/platform;/modules; kld netpfe drv: ifpfed_eth ifpfed_ml_cmnkld platform: ex_ifpfe if_vcpkld peertype: peertype_hcm peertype_pfem peertype_sfi peertype_slavere grat_arp_on_ifup=YES: net.link.ether.inet.grat_arp_on_ifup: 1 -> 1 ipsec kld. Doing additional network setup:. Starting final network daemons:. setting ldconfig path: /usr/lib /opt/lib starting standard daemons: cron. Local package initialization:. Initialize /var subdirs starting local daemons:set cores for group access . Sat Feb 4 10:42:04 UTC 2023 Boot media /dev/da0 has dual root support ** /dev/da0s2a FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 111117 free (61 frags, 13882 blocks, 0.0% fragmentation) Amnesiac (ttyu0) login: root --- JUNOS 12.3R12-S12 built 2018-12-28 12:55:38 UTC root@:LC:0% |